看了非接觸型直流扭矩傳感器的用戶又看了
留言詢價
虛擬號將在 180 秒后失效
使用微信掃碼撥號
Nonlinearity (% of F.S.)
=< ±0.15
=< ±0.07
Hysteresis (% of F.S.)
=< ±0.15
=< ±0.07
Nonrepeatability (% of F.S.)
=<±0.07
=< ±0.03
Accuracy (combined Nonlinearity， hysteresis and nonrepeatability， % of F.S.)
=<±0.15
=<±0.08
Stability， 6 Months (% of F.S.)
=<±0.20
=<±0.10
Rotational Effect on Zero (% of F.S.)
=<±0.10
=<±0.03
Calibration Accuracy (% of F.S. @ 75 deg F， traceable to NIST)
=<±0.05
=<±0.02
Temperature Effects:
Zero (% of F.S./deg. F.)
=<±0.003
=<±0.0015
Span (% of Rdg./deg. F.)
=<±0.003
=<±0.0015
Compensated Range
+75 to +175 deg. F
+75 to +175 deg. F
Minimum Useable Range
-25 to +185 deg. F.
-25 to +185 deg. F.
Storage Range
-65 to +225 deg. F.
-65 to +225 deg. F.
Zero Balance
=<±1% of F.S.
=<±1% of F.S.
Outputs: Fully bi-directional， dual outputs with characteristics as follows:
Clockwise (CW) Torque
+ 5 Volts
Counterclockwise Torque (CCW) Torque
- 5 Volts
Overrange (% of F.S.)
±33
Measurement Bandwidth:
High Frequency， dc to 500 Hz
Low Frequency， dc to 1 Hz
Power Supply Requirements:
10.5 to 24 Volts dc at 85 mA， nominal
技術參數：
扭矩范圍：0.071-452400N-m， 過載：200%
信號輸出：±5V，±10V，可以直接連接到PC，PLC或數據采集器
頻率響應范圍：1-500Hz
主要特點：
DC Operated Torquemeters are available in capacities from 25 lbf-in to 4，000，000 lbf-in with overload ratings of 2X full scale. Integral signal conditioning provides dual ±5 volt dc outputs proportional to torque. They will operate from a single power supply in the range of 10.5 to 24 volts dc (such as 12 volt batteries)
When installed between a driver and load， the sensor will measure static and dynamic shaft torque and speed (optional). A strain gaged stainless steel shaft senses torque and cancels bending and thrust. Robust， ferrite free rotary transformers connect the gages to noise immune carrier amplifiers. They don't generate noise or wear， are immune to magnetic fields， noise， vibration， lubricants and other hostile environments.
They are available in either shaft or flanged style configurations. Shaft end torquemeters are less costly than flanged models and can be either floated or foot mounted. Flanged models are much shorter and can be used when axial space is limited or when the highest shaft stiffness is needed
暫無數據！
非接觸型直流扭矩傳感器的工作原理介紹？非接觸型直流扭矩傳感器的使用方法？非接觸型直流扭矩傳感器多少錢一臺？非接觸型直流扭矩傳感器使用的注意事項非接觸型直流扭矩傳感器的說明書有嗎？非接觸型直流扭矩傳感器的操作規程有嗎？非接觸型直流扭矩傳感器的報價含票含運費嗎？非接觸型直流扭矩傳感器有現貨嗎？非接觸型直流扭矩傳感器包安裝嗎？
手機版：
工商已核實
